Sorry - this product is no longer available

Massoth eMotion LS 'Emma' set

eMotion LS and Powercap Micro for the LGB22222 'Emma' locomotive. Note: Loco not included.
Manufacturer: Massoth
Availability: Temporary Out of Stock.
SKU: me8201001
Manufacturer part number: 8201001

The most famous locomotive in the world! It lives on the Isle of Lummerland, its best friend is Jim Button, and its locomotive engineer is Lukas. That is Emma, probably the most famous locomotive in the world. Go with Emma, Jim Button, and Lukas on a trip full of adventure. Jim Button and Lukas the locomotive engineer from the movie of the same name based on the story by Michael Ende.

Scope of Supply:

1 x 8211100 eMotion LS sound decoder pre-loaded with the 8211570 'Emma' sound project.

1 x 8156101 eMotion Powercap Micro

eMotion LS:

Small 1.5 Amp sound decoder (up to six audio channels) with 6 function outputs, suitable for 1 motor.

eMOTION LS the decoder for the little ones.
Now there is also a sound decoder for small, single-engine model trains.
The eMOTION LS sound decoder is a driving decoder combined with a high-quality sound output stage with 6 usable sound channels.
The sound output stage is of the same high quality as the big brother XLS.
Despite its minimal size, the eMOTION LS has 6 function outputs.

Of course the eMOTION LS sound decoder has the same optimal analog and digital driving characteristics as the XLS
The sound functions are available from just a few volts.
Braking via break on DC is also possible (braking via a specially polarised DC voltage.

The eMOTION LS fully supports the NMRA DCC protocol. Due to the automatic detection for LGB® MZS systems, the eMOTION LS sound decoder is also suitable for all generations of the LGB® MZS multi-pull control system.
An LGB control or Susi interface is integrated.

ORIGINAL SOUND in digital quality
The eMOTION LS sound decoder reproduces the authentic sounds of a locomotive in high-quality digital quality. For this purpose, sound recordings are made directly on the model and then adjusted in the sound laboratory for the electronics. The eMOTION LS sound decoders have a total playback time of up to 145 seconds at their disposal. This enormous storage volume is sufficient to provide the sound decoder with various additional sounds.
The volume of the 4 sound phases can be adjusted independently of each other:

  • activation phase
  • stationary noise
  • deactivation phase
  • driving noise

State-of-the-art technology and the latest procedures allow new software to be loaded directly via the programming track. This guarantees updateability for the future without various generations of programming devices and also ensures the programmability of new and future sound decoder generations.
We would like to point out once again that a sound or firmware update is only possible via our PC module (8175101)!

Powercap Micro:

The available space for the installation of previous voltage buffers is often too small. Especially small, two-axle locomotive models (light rail locomotives) often show weaknesses in power consumption.
Running over a switch with a plastic heart when driving slowly quickly leads to a standstill. This can be intercepted by means of a voltage buffer.

Reserve for up to 30 seconds!
The eMOTION Powercap micro is used to bridge short interruptions in the track voltage of small 1-motor locomotives. The motor and the special functions are supplied from the memory during this interruption. This means that locomotives can easily run over points or insulation points without stopping. Due to its small dimensions, the Powercap micro can also be easily installed in small locomotives. The duration of the buffering is up to 30 seconds, depending on the connected load, current speed and state of charge of the memory.

Universal digital use & intelligent technology
With its sophisticated design and the use of special powercap capacitors, the voltage buffer with integrated charging circuit and charging function deactivation for decoder programming is suitable for use with almost all digital decoders that provide the + and decoder contact directly. (tested on: Massoth, LGB®, Lenz©, Zimo©)

Direct connection of the Powercap micro to the eMOTION L/XL(S) locomotive decoder
The Powercap micro is particularly suitable for connection to the eMOTION L/XL(S) locomotive decoder. As usual, the contacts decoder + (red) and decoder – (black) are used. The third cable (white) is used to switch off the charging function when the contact is open. This function is performed by a function output of the eMOTION L/XL(S) locomotive decoder. The charging function is automatically switched off when the decoder is being programmed or read out. The programming process can therefore be carried out correctly. For external decoders, the additional switch included in the scope of delivery is used.

  • Buffer time up to 30 seconds (load-dependent)
  • maximum buffer current 1000mA
  • maximum charging current 400mA
  • Power supply 6-24V= (DC)

Customers who bought this item also bought